A20 Roadworks between Hollingbourne Corner and the Leeds Castle Roundabout.

When:
24th July 2018 @ 9:30 am – 3:30 pm
2018-07-24T09:30:00+01:00
2018-07-24T15:30:00+01:00
Where:
Great Danes Hotel.
Maidstone ME17 1RE
UK

Hollingbourne Parish Council has been advised by Kent County Council of these roadworks on the A20. Please see below for a message from Kent County Council or download the formal notice at  SoWN-24-07-18-A20-Ashford-Road-Hollingbourne-Maidstone-SD.pdf (24 downloads)

Road Maintenance in Your Area Road Surface Improvement (Surface Dressing)

A20 Ashford Road, Hollingbourne, Maidstone

When we plan to carry out the work and how long it will take This is to let you know that, as part of the on-going maintenance and improvement of the highway network, Kent County Council will be working to improve the road surface of A20 Ashford Road, Hollingbourne, Maidstone between Hospital Road and B2163 Penfold Hill roundabout.

These road surface improvement works are programmed to start on the 24th July 2018 and should take 1 day to complete. These activities will be undertaken during a short working window between the hours of 9.30am and 15.30pm during this day.

This type of work can be affected by bad weather, so if it is not possible for us to carry it out at this time, we will arrange a new date and let you know via a letter drop to your home. We will also put up signs along the road before we start showing the date we plan to start work.

During these essential works it will be necessary to control the traffic with stop/go boards.

The timings of works and how the ‘working window’ may affect you Our surfacing improvement (Surface Dressing) is a very quick process and usually takes no more than half a day to complete. We therefore undertake a programme of several surfacing sites in a day, following on consecutively from each other, to maximise the economy of our surfacing. Consequently, it is not possible to give an exact time when we will attend your road in advance of the works as this is dependent on the progress at other sites during the day, however the works are programmed to be undertaken within the working window specified above.

Where we have specified the works may take place over 2 or more days we would expect our operatives to be on site on either of these days, again for a few hours in a single visit. Surface Dressing is a quick process but is also heavily dependent on good weather and site conditions. By allowing for extra days we can ensure that unforeseen circumstances to our works can be accommodated and disruption to local residents is minimised.

What we plan to do We will use a process called ‘Surface Dressing’ to improve the road surface. Surface dressing is quick to apply, which means less disruption to road users, residents, local businesses and the emergency services. It is a cost-effective way of prolonging the life expectancy of the road before any major repair works are required. It also benefits from having a low carbon footprint.

Surface dressing is applied directly onto the existing road in two stages. The first is the application of a hot binder which is sprayed onto the road surface and the second is the laying of chippings onto the binder. (Sometimes we lay 2 or more layers of chippings depending on the design). These layers seal the surface to prevent water penetration, restore texture and improve skid resistance. The carriageway may then be rolled using a rubber wheeled roller. This is to ensure the chippings are properly embedded and stick into the binder permanently. The continued action of the traffic also helps to embed the chippings as well.

To make sure all the binder is covered with chippings, we lay enough onto the road to ensure a full covering, and to make certain there are no gaps. There will be some loose chippings left, which is quite normal, and consequently we erect 20mph speed limit signs to slow vehicles down as they pass over the new surface. These signs will be on site until the road has settled down and all programmed sweeps have been carried out.

Generally, after 14 days of the completion of the surfacing the road markings will be reinstated

Further Information on this treatment process

Further information on Surface Dressing, including a short video presentation, can be found on our website at www.kent.gov.uk/roads-and-travel/what-we-look-after/roads/road-resurfacing/types-of-resurfacing.

Alternatively, this video can be found on YouTube by searching for ‘Kent County Council Surface Dressing’.

How you can help It is inevitable that residents and businesses near the works will experience some disruption, but we will try to keep these to a minimum. Any pavements will remain open at all times, but vehicle access to properties will need to be restricted for a short period while work is carried out in front of each property. If you have any particular access needs, please let the workforce on site know. We need your help to make sure the work is done as quickly as possible and to the best possible quality.

If your vehicle is usually parked on the carriageway, please make sure you park it somewhere else away from the site whilst the works are carried out, so the road is clear for us to resurface.

If you need more information, please call us on 03000 41 81 81 You can also visit our website www.kent.gov.uk/highways to find out how we look after the roads throughout Kent or report any faults you find on our roads.

For your safety and the safety of our workforce, please drive carefully and slowly through the roadworks.

WARNING – Beware Bogus Callers Kent County Council Highways, Transportation and Waste do not allow works to be carried out on private properties. If anyone says they are working for us or our specialist contractors and offer to carry out any work for cash, they should be treated with caution. We advise you to contact Citizen’s Advice on 03444 111 444 (Monday to Friday 9.00am to 5.00pm)